Toro Greensmaster® TriFlex™ 3320

The Greensmaster® TriFlex™ Mowers were designed to take precision cutting on a greens mower to a completely new level. Adopting the proven Flex suspension, the cutting units float freely over contours and undulations of the green resulting in a superior quality of cut and aftercut appearance. Improved serviceability is another major advantage of the TriFlex™ models. The tool-free, quick-change cutting units make servicing the cutting units fast and easy and a lift-gate footrest provides easy access to the center cutting unit.

ENGINE	Briggs & Stratton® Vanguard®, 21 HP (15.6 kW) @ 3600 rpm, 2-cylinder, air cooled, gasoline engine, governed to 2920 high idle, 1650 rpm low idle. Displacement: 38.3 cu-in. (627 cc)
FUEL CAPACITY	6 gallons (22.7 liter) capacity
TRACTION DRIVE	2WD parallel hydrostatic or optional 3WD series-parallel piston pump closed loop system. Foot pedal forward and reverse; infinitely variable.
GROUND SPEED	Forward-mowing speed is variable from 0-5 mph (0-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum Greensmaster TriFlex transport speed is 10 mph (16.1 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds.
CUTTING UNIT DRIVE	48V-5400 watt air-cooled brushless permanent magnet generator in parallel with 48V 9Ah battery set powers three 48V- 1100 watt brushless permanent magnet reel motors.
AUTOMATIC CLIP CONTROL	Yes
STEERING	Power steering. No-tool quick adjust steering arm position with power assist, allowing a wide range of operator sizes. Steering cylinder has a through shaft design for precise straight line tracking.
ELECTRICAL SYSTEM	12-volt lead acid, group size U1, with 300 minimum cold cranking amps at 0° F and 34 minutes reserve capacity at 85° F/25 amps draw. 50 amp alternator. Ignition switch/key. Seat switch. Harness terminals and fuse slot available for optional lights installation.
48-VOLT SYSTEM FOR ELECTRIC REELS	4-12V 9Ah sealed, maintenance-free, VRLA batteries. 48-volt system is isolated from 12-volt including the frame/chassis.
CONTROLS	Ignition: Off/Run/Start. Throttle: Low – High Idle. Choke (AC only): Open /Closes choke plate. Parking Brake: Off – On. Traction Pedal: Rev/Neutral/Forward Joystick: Raises/lowers reels also tap off feature for clean up pass. Functional Control Lever sets neutral/mow/transport limits for traction pedal. Diagnostic Light: Indicates system faults to assist in resolving issues (04510 & 04520). InfoCenterTM Diagnostics (04530 & 04540).
GAUGES	InfoCenter™: Onboard LCD shows gauges, alerts/faults, service reminders, electrical system diagnostics, low oil pressure, alternator, engine hours, engine rpm, voltage, functional control status, parking brake applied, reel speed setting, backlap control. Clip control setting.
TIRES/WHEELS/PRESSURE	Three, 19 x 10.5 x 8, 4-ply rating pneumatic tubeless and demountable. Smooth tread. Tire pressure recommended: 12 – 18 psi front and rear.
BRAKES	Hand-actuated parking brake lever with two 6” (15.2 cm) diameter drum brakes mounted on the front wheel motors.
HYDRAULIC OIL	5.5 gallon (20.8 liter) tank
LEAK DETECTION	Optional
SOUND LEVEL	80 dB(A) at operator’s ear under normal conditions.
OVERALL DIMENSIONS	Wheel Track: 50.5” (128.3 cm) Wheel Base: 47” (119 cm) Length: 98” (249 cm) Width: 70.84” (180 cm) w/reels Height: 80.83” (205 cm)
WEIGHT	1257 lbs. (570 kg)
WIDTH OF CUT	59″ (150 cm)
GROUND CLEARANCE	4.5” (11.4 cm)
CUTTING UNIT SUSPENSION	Double A-arm suspension utilizing sealed ball joints allows free cutting unit motion in pitch, roll, and yaw. The basket is directly mounted to the cutting unit displacing weight evenly over both cutting unit rollers eliminating the carrier frame, roller and pull links. Lift in Turn: Provides a level cut from side to side of cutting units regardless of turning angle (patented).
QUICK CONNECT CUTTING UNITS	Quick connect/disconnect feature for both the reel drive motor and cutting unit. No tools required.
REEL SPEED	Approximately 2050 RPM at 2850 engine RPM. Adjustable.
BACKLAPPING	Standard equipment
OPTIONAL ACCESSORIES	Canopy, verticutters, greens rollers, dethatchers, oil cooler.
CERTIFICATION	Certified to meet ANSI specification B71.4 – 2004 and European CE standards.
WARRANTY	Two-year limited warranty. Refer to the Operator’s Manual for further details.